Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Buffalo, TX to inspect, repair, and replace with zero guesswork.
We didn't start Forge Siding to push volume — we built it because homeowners in Buffalo kept getting burned by crews who cut corners on material selection, skipped moisture barriers, and left job sites messy. That's not how we work. Every Siding project starts with an honest assessment: we look at your substrate condition, check for existing rot or moisture intrusion, and talk through your options before a single nail goes in.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Even a small gap at a butt joint or around a window trim is an entry point. Water wicks in, freeze-thaw cycles widen the gap, and the damage compounds every winter.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Compromised siding reduces your wall assembly's thermal performance. If you've noticed climbing heating or cooling costs without an obvious cause, degraded siding — especially if it's letting air infiltrate — is worth investigating.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
Every job below starts with a free written estimate. We specify the product, the profile, the color, and the installation method upfront — so there's no ambiguity when work begins.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for TX's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
LP SmartSide and similar engineered wood products split the difference between the look of real wood and the dimensional stability of manufactured products. They're primed at the factory, accept field-applied paint well, and hold up to impact and moisture better than OSB or solid wood. We use LP SmartSide Trim & Fascia alongside the panel and lap systems so the trim package matches — no mixing incompatible products that age differently.
Our repair crews use the same material standards as our full-installation teams — no caulking over gaps as a permanent fix, no missing sealant at transitions, no shortcuts on housewrap at the repair perimeter. If there's rot in the sheathing behind the damaged panel, we address it during the repair rather than covering it up.
Commercial and multi-unit projects have different demands — larger panel formats, longer exposure to foot traffic and equipment contact, stricter fire ratings in some occupancy classes, and coordinated scheduling with other trades. Forge Siding handles commercial cladding projects in Buffalo, TX with full project management: dedicated site supervisor, daily progress reporting, and material delivery coordinated to minimize storage and laydown area on constrained sites.
Siding that terminates at rotted or missing fascia boards isn't protected — it's channeling water straight into the rafter tails. We routinely pair siding replacement with trim, soffit, and fascia work so the entire exterior envelope is addressed in one mobilization rather than two. PVC trim board, prefinished aluminum coil, and fiber cement fascia are all in our wheelhouse.
Four steps. Each one documented. No surprises at the invoice.
We come out, examine your existing cladding, probe for soft substrate, check flashing and housewrap condition at visible penetrations, and give you an honest assessment of what we're working with. No high-pressure sales — just a clear picture of the project scope before we talk numbers.
The estimate covers every line item — material, labor, disposal, permit fees if required in your jurisdiction. You pick the product, the profile, and the color with our input on what's going to perform best for your specific wall orientation, climate exposure, and substrate condition.
We schedule your project start date at contract signing and stick to it. Materials are delivered directly to the site before crew arrival — no day-of scrambling. We protect landscaping, windows, and any surfaces adjacent to the work area before the first panel comes off.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Buffalo, TX on the fact that our estimates are reliable.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Call to Learn More — +1-844-782-0929Straight from the homeowners we've worked with across Buffalo and Buffalo, TX.
We had three other quotes before calling Forge Siding. The difference was the inspection — they actually walked the whole house with a moisture meter and found soft sheathing behind two panels on the north wall that nobody else mentioned. The estimate covered the sheathing repair too, so no surprise charges when demo day came. Final result is clean and tight. We'd hire them again without hesitation.
A storm took out a whole section of vinyl on the east side of our house. I called four contractors — three of them said they'd have to replace the entire elevation because they couldn't match the profile. Forge Siding's estimator sourced a matching panel through their supplier network and did a clean repair. You can't tell where the new material starts. Saved us probably $4,000 compared to a full-side re-do.
The fascia and soffit on our older home were rotting away and we assumed it would be a nightmare project. Forge Siding quoted it alongside the siding replacement so everything was done in one mobilization. The crew found two spots where the rafter tails had started to soften — they showed me photos before touching anything and walked me through the repair options. The whole exterior looks like a different house now.
The estimate process was refreshingly honest. The estimator told me upfront that my old OSB sheathing had delaminated in two areas and would need replacement before new siding could go on — with photos and a written line item. No one had mentioned that in the other quotes. Forge Siding fixed the sheathing, installed the HardiePanel system, and the project cost exactly what they quoted including the repair.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Buffalo, TX don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
Real questions, real answers — no filler.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Buffalo, TX. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Reach us at +1-844-782-0929 and we'll confirm service at your location. Most addresses in and around Buffalo are within our standard service radius with no travel fee.
Don't let failing siding go another season. Call Forge Siding and we'll have an estimator out to your property within 24 hours.
Schedule My Assessment — +1-844-782-0929